Walrus Audio SLOER Stereo Ambient Reverb
The Sloer Stereo Ambient Reverb builds on our popular Slo lineup but adds two additional reverb algorithms, stereo width control, two additional modulation wave shapes, and the ability to control the sample rate. Now you can create immersive, lush, modulated, sleepy, and ambient soundscapes with more width and depth than ever before.
Save your favorite dreamscapes with three onboard presets by simultaneously pressing and holding down on the bypass and sustain switches. Scroll through them by simultaneously pressing and releasing bypass and sustain.
The five-way rotary dial allows five different reverb modes – the three you know and love from the Slo: Dark (Lower Octave), Rise (Ambient Swell), and Dream (Latching Pad); and the addition of two new modes: Rain (Delay Tap Diffusion) and Light (High Octave Shimmer). Secondary functions on the dial change between five different wave shapes for modulation on the reverb trail.
Combine deep modulation, long washy trails, and an immersive stereo field to experience Sloer.
ALGORITHMS:
DARK – Add a lower octave to your reverb trail. Here you’ll create deep and wide atmospheric sounds and channel nightmarish soundscapes. X knob sets the level of a -1 octave signal that feeds the reverb.
RISE – This is an auto-swell reverb for beautiful cinematic swells. Don’t rush it. Let it breathe and gently wake up. X knob sets the amount of time it takes the reverb to swell in after a note is played. Set lower for shorter rise times and higher for longer rise times.
DREAM – Lush reverb with a latching pad function. Press the sustain switch to latch signal. Experiment with the X knob to add vibrato over the pad. Press sustain again and the pad will decrescendo according to where the decay knob is set. X knob sets the depth of vibrato applied to the reverb trail.
RAIN – Tappy and trippy, this program creates a unique effect with lower levels of diffusion allowing the reverb delay taps to audible create an echo-like effect within your reverb. Use the Xcontrol to set the amount of diffusion of the delay taps.
LIGHT – Bright and smooth reverb with an octave-up shimmer. Create a range of ethereal sounds with the X slider, keep it low for a smooth pad-like reverb or push it higher for a bright shimmer effect.
Five different wave shapes
The Sloer also features five different wave shapes accessible by holding down bypass while switching the algorithm dial.
SINE – Smooth and even pitch up and down modulation.
WARP – Asymmetric pitch up modulation similar to a warped record.
SINK – Asymmetric pitch down modulation for sinking detune similar to a Bigsby.
SQUARE – Symmetric pitch up and down modulation for stepped modulation.
RANDOM – Uses sample and hold that picks new random values.
MOMENTARY FUNCTIONS:
Bypass: When the switch is in the off position, press and hold to temporarily activate the effect to add a moment of reverb texture. Releasing the switch turns the effect off, and fades it out.
Sustain: When pressed, the decay switch ramps up the reverb trail to maximum creating a long dreamy reverb trail, and then ramps back down to the decay knob setting when released. In the “Dream” algorithm, the sustain switch is latching. Press it once to capture and sustain the current reverb decay for extremely long pad-like sounds. Press it again to let the reverb trail taper off, based on the position of the decay knob.
TRAILS MODE:
The Sloer can run in trails or no trails mode. In trails mode, when you turn the pedal off, the reverb decay dies off naturally. In no trails mode, the decay is abruptly cut off when you turn the pedal off. To toggle between either mode, hold down the bypass switch for 1 second while applying power to the pedal. Unplug power and repeat to toggle to the other mode.
PRESET SPILLOVER
When scrolling through presets, there is only preset spillover if the next preset is the same algorithm as the one preceding it. For example, if your red and green presets are both in Dream mode, switching from red to green will not cut your reverb trails.
Specs
- The Sloer comes in a Lollipop Blue finish with light blue and off white ink featuring original artwork by Christi Du Toit,
- The die-cast enclosure’s exact size is 4.79” x 3.62” x 2.25” including knobs.
- Power requirements are 9VDC (100mA minimum).
- The use of an isolated power supply is recommended for powering all Walrus Audio Pedals. Daisy chain power supplies are not recommended.
- Power supply not included.
BOOM!
BOOM! 